• Permanent cementation of crown and bridge.
• ◆Permanent cementation of endodontic posts made of metal, reinforced composite.
• ◆Permanent cementation of implant retained crowns.
• ◆Permanent cementation of inlays/onlays veneers.

Self-adhesive dual cure resin cement for permanent cementation of ceramic composite metal and zirconia restorations.

This resin cements product is positioned within Zenodent’s Restorative range. Permanent cementation of crown and bridge. Base Paste: Bisphenol A Glycidyl Methacrylate, Urethene Dimethacrylate, Triethylene Glycol Dimethacrylate, Silanated zirconia silica Powder, Amorphous Fumed Silica, Curing Agents and Stabilizer.

The supplied retail pack contains 1 X 9 gm Syringe Review the manufacturer label and instructions before professional use.

• Base Paste: Bisphenol A Glycidyl Methacrylate, Urethene Dimethacrylate, Triethylene Glycol Dimethacrylate, Silanated zirconia silica Powder, Amorphous Fumed Silica, Curing Agents and Stabilizer.
• Catalyst Paste: Bisphenol A Glycidyl Methacrylate, Urethene Dimethacrylate, Triethylene Glycol Dimethacrylate, Silanated Silica Zirconia Powder, Amorphous Fumed Silica, Curing Agent and Stabilizer, Pigment. Intended Purpose/Intended Use: It is intended to be used for permanent cementation of indirect restorations.

1 Pack Contains:
• 1 X 9 gm Syringe

1. Dispense the material from syringe through automix tip. The initial set will occur in 2:00 2:30 (min sec) with a final set at 3-4 minutes. The cement may also be cured with a dental curing light with a 40 second exposure.
2. Metal to Enamel/Dentin: Metal restorations to tooth structure-crowns, inlays, bridges, and posts including Maryland and bridges) After try-in, sandblast each side of the restoration. Using a metal primer of your choice, treat the metal exposed to the paste. Clean tooth with non-fluoridated prophy paste or pumice. To prepare tooth for bonding, use a universal dentin/enamel bonding system. Mix equal Amounts of catalyst and base pastes and use a plastic instrument or injection system to place in restoration. Avoid trapping air bubbles. Seat Restoration on tooth and hold in place until paste reaches initial set (about 2:00-2:30 minutes). Use a scaler or explorer to remove excess. cement immediately upon initial set. It is not important to wait until the final set to remove excess cement.
3. Metal to Metal: Implant prosthesis or crown on post. Sandblast all external metal surfaces to be exposed to paste. Rough intra-oral metal with a micro-etcher or bur. Using a metal primer of your choice, treat the metal exposed to the paste. Clean posts or Abutments with non-fluoridated prophy paste or pumice. Mix equal amounts of catalyst and base pastes and use a plastic instrument or injection system to place in restoration. Avoid trapping air bubbles. Seat restoration on tooth and hold in place until paste reaches initial set (about 2:00-2:30 minutes). Use scalar or explorer to remove excess cement immediately upon initial set. It is not important to wait until final set to remove excess cement. 3. Ceramic Restorations to Teeth (Porcelain Veneers, In-lays, On-lays) After try-in, etch ceramic restoration and place in acetone or ethanol in ultrasonic cleaner for 1-2 minutes. Place silanating agent on internal or porcelain restoration. Clear tooth with non-fluoridated prophy paste or pumice. To prepare tooth for bonding, use a universal dentin/enamel bonding system. Mix equal amounts of catalyst and base pastes and use a plastic instrument or injection system to place in Restoration. Avoid trapping air bubbles. Seat restoration on tooth and hold in place until paste reaches initial set (about 2:00-2:30 minute) use scalar or explorer to remove excess cement immediately upon initial set. It is not important to wait until final set to remove excess cement. The dispensed material shall not be placed back in container and the dose once applied and used shall not be reused.

Manufactured by: Vishal Dentocare Private Limited, India

Not Applicable