* Features high contrast coloration between green putty and yellow wash material to facilitate effortless margin reading.
* Delivers optimal fluid dynamics in the wash phase to record minute subgingival and preparation contours accurately.
* Offers superior tear strength to minimize distortion or marginal tearing during impression removal from undercut areas.
* Maintains dimensional stability following surface disinfection procedures, safeguarding master model accuracy.
* Formulated with non-irritating, biocompatible raw materials to ensure clinical safety on damaged oral mucosa.
* Provides adequate final shore hardness to withstand stone pouring without surface compression.
* Infused with a pleasant mint fragrance and flavor to increase patient comfort during intraoral setting.
* Ensures predictable working times and snap-set characteristics for enhanced clinical handling efficiency.

The NeoEndo Neopure C-Silicone Impression Material Kit offers a complete, reliable, and high-precision condensation silicone solution tailored for everyday prosthodontic routines. Formulated using premium polysiloxane polymers, this system exhibits high viscosity control in the putty phase combined with optimal flowability in the light body wash material. It is ideal for double-step (two-phase) or single-step wash impression techniques, effectively reproducing complex crown preparations, bridge abutments, inlays, onlays, and complete denture borders down to 20 microns.
Designed with distinct color contrast—a vibrant green putty base paired with a high-visibility yellow wash—the system simplifies visual inspection of critical preparation finish lines. The low linear shrinkage rate and elastic recovery above 98% ensure master casts poured from Neopure impressions retain exact dimensional fidelity. Added patient-centric features, such as a pleasant mint flavor and odor, significantly reduce gag reflexes and enhance compliance during the intraoral setting phase.
Each kit comes fully equipped for immediate clinical deployment, including a generous 1500 g bulk putty tub, 140 g light body tube, 70 g universal catalyst gel, and a dosage-calibrated measuring scoop.

* Material Type: Polysiloxane Condensation Silicone (C-Silicone)
* ISO Standard: ISO 4823 (Putty: Type 0 Consistency, Light Body: Type 3 Consistency)
* Putty Consistency & Color: High viscosity, Green
* Light Body Consistency & Color: Low viscosity, Yellow
* Mixing Time: 30 seconds (Putty and Light Body)
* Working Time: 1 minute 30 seconds
* Intraoral Setting Time: 3 minutes (Putty), 3 minutes 30 seconds (Light Body)
* Total Setting Time: 4 minutes 30 seconds (Putty), 5 minutes (Light Body)
* Dimensional Shrinkage: < 0.2% (Putty), < 0.7% (Light Body)
* Elastic Recovery: > 98% (Putty), > 99% (Light Body)
* Detail Reproduction: 20 µm
* Flavor/Odor: Refreshing Mint

1 Pack Contains:
* 1 × Neopure C-Silicone Putty Base Tub – 1500 g
* 1 × Neopure C-Silicone Light Body Tube – 140 g
* 1 × Neopure C-Silicone Universal Catalyst Gel Tube – 70 g
* 1 × Measuring Scoop

1. Dispense one measuring scoop of Neopure C-Silicone Putty Base onto a clean mixing pad or palm.
2. Imprint the rim of the measuring scoop into the putty surface and apply two full lines of activator gel across the diameter.
3. Knead the putty base and catalyst gel vigorously with fingertips for 30 seconds until a uniform, streak-free green color is achieved.
4. Load the mixed putty into the impression tray and insert into the patient's mouth within 1 minute 30 seconds of mixing.
5. Squeeze equal lengths of Neopure Light Body wash and activator gel onto a mixing pad, then spatulate thoroughly for 30 seconds until homogeneous.
6. Syringe the light body wash around the prepared tooth structures and seat the secondary impression tray, holding passively for 3 minutes 30 seconds intraorally.
7. Remove the set impression firmly along the long axis of the teeth, inspect for marginal accuracy, rinse under water, and disinfect prior to model casting.

Manufactured by: Orikam Healthcare India Pvt. Ltd., India

Not Applicable